1939 CCM Motorbike pedal info required

Submitted by realjolt on Tue, 07/02/2013 - 22:51

Hi everyone. My wife and I are the proud owners of inherited vintage CCM bicycles. A men's 1939 (according to the serial # I found on this site) CCM Motorbike and a 1945 CCM Ladies bike Unfortunately the left pedal on the Motorbike failed a few days ago and l am not entirely sure as to how the pedal is attached to the crank arm. It appears the bolt on the end of the pedal axle snapped leaving only the axle without any rubber. Info on aquiring a repair/service manual or exploded view would be great. Would like to keep it as original as possible but willing to go with newer stuff if need be.See attached photos.

11 Comments

Submitted by realjolt on Tue, 07/02/2013 - 22:52.

Photos soon!

Submitted by william rudolph on Mon, 07/15/2013 - 22:55.

the left pedal non chain ring side can be removed with a 9/16 pedal wrench by turning it clockwise it is a 1/2 inch 20 threads per inch left hand thread if you post a picture of the other pedal maybe someone can help  william rudolph

Submitted by realjolt on Thu, 08/29/2013 - 17:54.

Thanks for the tips but unfortunately I don't have a pedal wrench. I stripped the bike down to the bare frame and and took it to the nearest bike shop. After a couple of days the shop called me back and were unable to remove the left pedal. He was worried he would snap it off. Okay so on the way back home I dropped it off at a machine shop whose owner said he could get it off. The next day he called and said that even with having applied a little heat it still snapped off. NO! He then added he was able to drill through the center of the broken pedal stub and chip out the remains and saved the threads.Whew! I found some rubber pedals that were a close match and was riding again until a couple days ago. Looks like I need a replacement outside bearing and cone on the rear hub.It's the one which rides between the cup in the sprocket assembly and the cone. The ball bearings are there but no ring to hold them in place. It appears the cone has some serious wear in two places because of that. New advice anyone?

 

PS..... Any info on uploading photos on the site?

Submitted by william rudolph on Sun, 09/01/2013 - 15:27.

ccm  37 hub parts i have a new bearing cage with new 1/4"bearings and a cone that will work it is from a ccm 64 model hub each part is $5.00 plus shipping no handling charge.i can be reached at 1-902-477-9734 send me your address and i can put it in the mail to you  if you need more  your out of luck that is my last onehope this helps william rudolph

Submitted by John on Sun, 09/01/2013 - 20:28.

realjolt if you want to send the photos to me I'll post them for you

John

john.mckenty@sympatico.ca

 

Submitted by william rudolph on Thu, 09/12/2013 - 17:27.

your parts were shipped today by canada post $10.00 for the parts plus $1.55 shipping total $11.55 hope they reach you soon keep me posted when they arrive   william rudolph

Submitted by realjolt on Tue, 09/17/2013 - 18:30.

Thanks William, the parts arrived today. Great job packaging! Money's on the way. Misunderstood the total $. Will be arriving in two envelopes.

 

Hey John did you get the photos?

 

Joel

Submitted by John on Thu, 09/19/2013 - 09:41.

Just back from the west coast. Sorry for the delay Joel. Here are the photos:

Submitted by realjolt on Thu, 09/19/2013 - 15:39.

Hope you had a nice trip out west! These bikes are so much fun to ride. Unfortunately we had to leave them behind at the family cottage on Lake Winnipeg. Our home is in Alberta but we're already thinking about next summer!  

Submitted by John on Fri, 09/20/2013 - 21:36.

Thanks Joel. We had a great time in the west. Didn't hardly see half of it tho. Will have to go back. Maybe get Lawrence to give us a tour....by bike, of course.

John   

Submitted by william rudolph on Wed, 09/25/2013 - 09:21.

two cheques recieved thanks william rudolph